Product finder

100 Ton Die Sets for hydraulic crimping tools

Die sets for 100 ton hydraulic crimpers. Works with 100 ton presses which accept shell type dies including the Slingco TCR08490. Available in many sizes for different Circumferential or Hexagonal profiles (CD, AH, SH).

10k Drive Wrench Assembly

Slingco’s 10k Drive Wrench Assembly is a tool system for the installation of screw anchors. Designed to connect the square anchor of a drive motor or screw anchor to the hexagonal Kelly Bar of a bucket truck. System options include Drive Wrenches to suit different sized anchor rods; a Drive Wrench lock; two Kelly Bar Adapters to fit the hex drive bar’s dimensions (2.5 in and 2.625 in) and one Square Head Kelly Bar Adapter to suit 3 in Square Drive Bar. The Drive Wrench Lock attaches to the Kelly Bar Adapter and makes the installation of the Anchor Rod much easier. The three-position rings of the lock assembly ensure easy capture of the Drive Wrench and Anchor Rod, holding them securely while under torque and releasing them when needed. The Drive Wrenches are designed to allow Anchor Rods to telescope inside, and secure to, the Drive Wrench Lock. The Drive Wrench transfers the torque from the Drive motor to the Screw Anchor, and are rated to 10,000 ft-lb.

2K Strap Hoist

The Slingco 2K strap features a hi-viz yellow strap for easy identification. In single line mode capacity is 1K. When used in double line mode capacity is 2K. The 2k Strap Hoist has a pressure die cast drum for professional look and smooth finish to minimize the risk of strap fraying. The strap hoist has three operating positions: lift/pull, lower/release, and freewheeling. For information while in the field, use the QR code on Slingco products to quickly reach manual and helpful information on your mobile.

3k Strap Hoist

Use the Slingco 3k Strap Hoist to splice, dead end, and sag lines. The Slingco 3k Strap Hoist features an interlocking pawl lever system with dual pawl springs for controlled tightening and releasing of the strap and to ensure the hoist is engaged while in use. The strap hoist complies with ASME B-30-21 standard and all units are tested to 125% of load. The Slingco 3k Strap Hoist uses pressure die castings for a professional look, consistent material properties, and smooth finish. The strap is hi-viz bright green in color for easy visibility. The strap hoist has three operating positions: lift/pull, lower/release, and freewheeling.

4K Strap Hoist

The Slingco 4K Strap Hoist features a hi-vis blue strap for easy identification. In single line mode capacity is 2K. When used in double line mode capacity is 4K. The 4k Strap Hoist has a pressure die cast drum for professional look and smooth finish to minimise the risk of strap fraying. The Strap Hoist has three operating positions: lift/pull, lower/release, and freewheeling. Strap Hoists come in standard and hot stick operable versions.

60 ton Die Sets for hydraulic crimping tools

Die sets for 60 ton hydraulic crimpers. Works with 60 ton presses which accept shell type dies including the Slingco TCR7003 and TCR7018. Available in many sizes for different Circumferential or Hexagonal profiles (CD, AH, SH). Slingco Die Sets are made of 4140 steel alloy.

90° Connectors

Use to connect rope, swivels and other objects. With high strength pins and smooth rollers you can safely connect rope without fear of fraying or damage. Use the convenient 90° connectors to link wire and other non-rope items. Connectors have high strength hex pins.

A Type - High Strength Cable Socks

The strongest sock we produce; can be used for metal wire and synthetic rope pulls. Perfect for overhead transmission and distribution line pulling or any applications with heavy load ratings, e.g. gas, electric railroad, rigging lines and construction pulls. When pulling synthetic rope use a Slingco Feed Tube to make rope insertion a breeze. To avoid the effects of torsion a line pulling swivel that rotates under load should be used. Galvanised steel and colour coded for ease of identification. High strength A-Type socks recommended when pulling guy or static wire.

Anchor Buster

The Slingco Anchor Buster - a dual-purpose powerhouse: Multi-functional tool for busting open expanding anchors and tamping dirt Engineered for the uncompromising demands of utility and construction environments, the Slingco Anchor Buster is a specialised 10-foot manual tool that provides both power and precision. It is built for two critical stages of pole setting and earthwork: expanding anchors and tamping backfill. Key capabilities The Anchor Buster is built for tough field conditions and provides the leverage and durability crews need on the job: Anchor expansion: The primary function is to ‘bust open’ expanding anchors. The 10-foot length gives crews the leverage needed to drive expanding anchors fully into undisturbed soil, helping achieve proper anchor holding strength. Precision tamping: The tool features a weighted head designed to pack soil back into place. It compacts soil tightly around the anchor, reducing air pockets and helping prevent settling or shifting over time. Why professionals choose the Anchor Buster In an industry where equipment downtime is costly, the Anchor Buster offers a reliable, manual alternative to hydraulic or pneumatic systems. The manual design gives operators direct control over each strike, making it easier to feel when the anchor is properly set. Built from heavy-duty materials, the Anchor Buster is made to handle repeated impact in tough soil conditions. It’s a dependable tool for crews who need equipment that won’t fail in the middle of a job.

Anchor Rod Pulling Eye Assembly

Attach guy wire to ground anchors safely. Slingco's Anchor Rod Pulling Eye is used to position anchor correctly using Slingco's hoist when connecting guy wire. The Slingco anchor rod pulling eye installs on 0.5” to 1.25” anchor rods and is used in conjunction with hoist to tension and install pole guy wires.

Anchoring Accessories

Anti-Rotational Device (ARD)

The device prevents the cable from twisting as it travels over pulling blocks. Left uncontrolled, the optical cable’s delicate glass fibers could be permanently damaged during installation. Stops cables from twisting as they pass over pulling blocks For use with fiber optic and OPGW cable Prevents irreparable damage to delicate fiber optics caused by cable twists during installation The ARD has weighted attachments that hang down while stringing, keeping the ARD vertical to stop cable rotation ARD attachments collapse in line, enabling them to travel easily over pulling blocks The ARD includes one 5,000 lb swivel attached to the head of the device

Ball Clevis - U Fitting

The CSB09095 is a galvanised standard U-ball clevis with a removable straight pin. The pin is held in place in the clevis body with a standard cotter pin.

Ball Clevis - Y Fitting

The CSB09094 is a galvanised Y-ball clevis with a curved holding bolt. The bolt is retained in the clevis body with a 1-1/8” hex nut and standard cotter pin. The curved holding bolt provides an additional point of manoeuvrability.

Banded Protectors

These lightweight, stamped steel protective cable guards offer a compact, low-cost alternative to our standard Cable Protectors. Designed for use in shallow wells with little to no deviation, the protectors are situated across the coupling and attached to the tubing string with steel bands.

Blanket Magnet

The Slingco Blanket Magnet is designed to fit through the eyelets of an insulated blanket. Afterwards, the magnet along with the blanket can be placed over energized areas of transformers, switchboards and substations. The Slingco Blanket Magnet is constructed of ultraviolet-stabilized fibreglass reinforced polymer. This reinforced polymer remains strong and resists breakage, providing a long life for the tool. Can be placed and repositioned with hot line tools.

Blanket Pins

Blanket Clamp Pins are used to hold insulating blankets and other types of rubber coverups in to place. The extra holes in the centre of the body are used to grip conductors and prevent linehose from sliding. The handles of the pin are shaped to engage into the end ferrule of a clampstick (shotgun stick). Also available with Hot Stick clip.

Blankets

Slingco insulating blankets are designed to cover irregularly shaped energized equipment that cannot be properly protected with other devices. They help prevent accidental contact with live conductors, apparatus, or circuits, and can be secured with blanket clamps, pins, or magnets. They are often used in place of insulator covers, cutout covers, line hose, and dead-end covers when a more adaptable protective solution is needed. Designed for safety and durability, these blankets meet ASTM D1048 standards offering protection up to 36,000V AC. Made from high-strength, ozone-resistant rubber, Slingco’s Type II Blankets provide flexibility in extreme temperatures. These blankets enhance workplace safety by protecting against electrical arcs, shocks, and flashes, making them ideal for utility workers.

Blast Protetors

Slingco Blast Protectors are designed to protect the cables servicing perforating guns in wells. We offer added metal in the protector channel to enhance locating the orientation of the gun through magnetic resonance. Protector styles are long length (56” to 96”) with added collars for securing the protector to the tubing. Call Slingco and let us to design a protector perfect for your application.

Bolt Cutters

When your work calls for a reliable, powerful cutting tool, turn to Slingco Bolt Cutters. Designed and built for the demanding, daily use of utility professionals and contractors, these cutters deliver consistent performance. Our hardened steel blades provide clean, powerful cuts across a wide variety of materials, including soft metals, chain, and rebar. The ergonomic handles are engineered for optimal grip and leverage, which helps reduce operator fatigue and improves control during tough applications. With a variety of sizes available, Slingco has the right tool for the job, helping you work efficiently and safely. WARNING: DO NOT use on energized lines.

Bow Spring Centralisers

Specially designed for vertical wells where low principal forces and high restoring forces are required, this one-piece design simplifies installation onto casings. The Bow Spring Centraliser is available in multiple sizes and blade configurations.

Bridge Type Cable Laying Roller

They are of steel construction with zinc plating for general purpose cable installation work in trenches. They are suitable for power, telecoms and utility installations, and can bridge existing cables in trenches or ducts.

BullWheel

Lightweight and portable, the Slingco Bull Wheel can be assembled by one person. It can also be dismantled and passed through a 3ft x 3ft access opening in the top of a concrete vault. Slingco has developed an 8ft wheel for stringing cables around 180º within underground vaults. The rotating wheel allows operators to impose a bend of up to Ø4 inches on conductor wire inside an underground concrete ‘vault’. Supplied with a two-point wall fixing, the wheel is mounted on an upright post that allows height adjustment between approximately 1ft to 7ft from the ground. Interchangeable circumference sections provide further options depending on application needs. Available in 6ft and 8ft diameter, the Slingco Bull Wheel can also be produced at different sizes to suit your application. The 6ft and the 8ft wheels are designed to withstand an imposed load of 8,000lb (SWL) with a factor of safety (FOS) of 3.

Bus Drop & Service Drop